10 TellTale Signals You Need To Know Before You Buy Fiat Panda Key Fob Replacement

replacement key fiat 500 with the fiat 500 number is a convenient method to open the doors and begin the car. There are a variety of reasons why the fob won't work. These include a dead coin battery, damaged receiver module, water damage issues, and interference.

This listing is for a NEW replacement Fiat Flip Key Remote - similar to the Ilco brand that must be programmed professionally by a local automotive locksmith (click here to search for a Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most frequent cause of your 500 key fob being inoperative. Modern key fobs have a very limited operating range, and should be within just a few feet of the vehicle to function. If you are further away from your vehicle and push the keyfob button it will not respond, and display the message "Key Fob Not Detected".

If this happens, simply replace the coin cell battery (Part number CR2032) by a new one from a reliable brand such as Panasonic, Duracell, or Energizer. They can be found in the local hardware store or on the internet.

You can test the battery on your coin-cell by pressing the buttons while you are standing close to your Fiat 500. The car will blink its parking lights, and the key fob should be able to operate the lock and unlock switches.

If the fob's key doesn't work after replacing the battery, it might have water damage that stops it from connecting to the receiver module in your vehicle. Water damage can happen in a variety of ways, from small splashes to submerging the fob into salt water at the beach. If you suspect that your fob was exposed to water, put it in a rice bag to draw out the moisture. If this fails, you'll need to have your fob reset by an auto locksmith or dealer.

Water Damage

Water damage can occur if you immerse the fob in the ocean or wash it in a washer. Saltwater can cause the circuit board to short and eventually die. It's not a good thing to let the fob get wet however, don't give it up if you accidentally drop it in water or forget to remove it from your pocket.

First take the battery off the fob. Clean the electronic chip with isopropyl alcohol or a similar product and dry it thoroughly before replacing the battery. Next try the fob and verify if it is working. If the key does not function, it may need to be reset. This is typically done by a professional or dealer auto locksmith.

If the key is more recent and hasn't been programmed to your vehicle it is likely to need to be replaced completely. This is a simple procedure which can be accomplished by a professional locksmith for automotive use. The locksmith must cut the key to match the ignition of your car. The locksmith will also need to reprogram the fob into the car's system. It's a simple and inexpensive process that can be completed on the next day.

Receiver Module Issues

Your 500 key fob may stop working because it is out of range. The remote usually has 30 feet of range or less and if it's far from your vehicle, it will not respond to your commands. You can fix this by moving the remote closer to your car until it responds.

If you've replaced the battery in your coin (commonly known as"button" or "button" or "watch") and your fob doesn't function, it could have an internal circuit board problem. Reprogramming the fob usually resolves this problem. There are instructions on how to do this on the majority of vehicles by searching YouTube or looking through the owner's manual.

It may be necessary to replace the metal clips that hold the coin batteries in their place. If they loose tension, it may prevent your battery from being properly seated and cause your remote to malfunction.

In rare cases, the fob may become disconnected from your vehicle because of software or hardware issues. You can fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain instances it is possible that the software will require reinstallation into your body control modules.

Interference

Interference can also cause the key fob to not receive or transmit an signal. This could happen if the key fob is close to an electronic radio transmitter (cell phones or radar detectors) or any other source of electromagnetic radiation. Other reasons the key fob might not function could be due to a weak connection to the buttons and internal chip, or water damage.





If your key fob suddenly stopped working, or you have tried everything at home to resolve it (e.g. battery replacement, reprogramming and using the spare key fob, it could have a malfunctioning receiver module on your 500. The receiver module is located under the dash and receives the radio frequency signals from the key fob. It converts the signals into electronic commands, which are then processed by the vehicle.

Fortunately, there's an easy method of resetting all of the onboard systems in your 500 and include the key fob. Disconnect the battery 12 volt for about 15 minutes by taking off the negative cable first then the positive cable. Reconnect the battery. This will clear any residual electricity, and restart the computer in your car. This can help you get your key fob to function again. If the issue persists, you should seek the advice of an expert technician. They'll be able determine the exact cause of your problem.